XT1 Charlie Toor folding knife: from Alpha to Charlie, the evolution of a frame lock built for the field

08.11.2026

Toor Knives, a San Diego cutlery house founded by a former US Marine, produces several versions of its XT1, the largest of its frame lock folders. After the Alpha and the Bravo, the XT1 Charlie is the latest variant. It drops the original recurve blade in favour of a drop point with a classic curved edge, swaps the carbon fibre spacer for G10, and comes down to 4.6 oz, roughly 130 g. The knife keeps the CPM S35VN steel, the thick blade and the reinforced lock that define the line. Sold among others by WETSU, a shop aimed at the American parachutist community, it is listed there at €359.95, out of stock in both colourways at the time of writing.

XT1 Charlie
359,95€
Buy On WETSU

Toor Knives, a cutlery house born of Marine experience

Toor Knives is based in San Diego, California. Its founder, Connor Toor, is a former US Marine who started out with a forge built in his backyard, a hammer and an anvil. The brand explains its approach with an observation from the field: Marines carried mass produced knives poorly suited to their missions, while high end blades remained expensive and slow to obtain. The company presents itself as founded and run by veterans, and claims in house manufacturing from machining to inspection, including grinding, finishing and assembly. In its catalogue, the XT1 belongs to the Folding Series, and the Charlie carries the Tactical and Concealable labels.

The XT1 Alpha, a folder built for heavy duty tasks

The line begins with the XT1 Alpha, designed by Connor Toor, Thomas Whard and Alfredo Garcia of the Toor team. The brief called for a folder able to withstand heavy military use, such as chopping cuts or prying. That brief shaped its proportions: a blade and handle larger than standard, and a reinforced lock. The Alpha was fitted with a 4 mm thick recurve blade, a titanium handle and spacer, for a weight of 5.6 oz. Each example carried an individual serial number, production ran in limited batches, and the knife shipped in a waterproof S3 case. It is now discontinued.

The Bravo introduces the hybrid handle

Launched in September 2022, the XT1 Bravo introduced the hybrid handle that defines the rest of the line. It added a stainless steel liner and a lock side with a polished and stonewashed finish, while the spacer switched to carbon fibre. The knife then gained weight, reaching 5.9 oz. Its blade already adopted the dimensions and steel that the Charlie would carry over unchanged. The Bravo thus marks a transitional step: the XT1's structure settles, while the handle materials diversify and the finishing grows more refined.

The Charlie, from tactical to all-rounder

The XT1 Charlie is presented by Toor as the latest variant of the XT1. Its main change lies in the blade: the original recurve gives way to a drop point with a classic curved edge, meant to make it a more versatile knife. The spacer drops carbon fibre in favour of G10, and the weight comes back down to 4.6 oz, roughly 130 g, the lowest figure of the three versions. The name follows the NATO phonetic alphabet that orders the line, from Alpha to Charlie, and the maker's product page slips in a wink, stating that even if Charlie doesn't surf, he still carries his XT1. The joke plays on a line from Apocalypse Now, the 1979 film, where ‘Charlie’ refers to the Viet Cong.

XT1 Charlie Toor 2 XT1 Charlie Toor 3 XT1 Charlie Toor 4 XT1 Charlie Toor 5 XT1 Charlie Toor 6 XT1 Charlie Toor 7 XT1 Charlie Toor 8 XT1 Charlie Toor 9 XT1 Charlie Toor 10 XT1 Charlie Toor 11 XT1 Charlie Toor 12 XT1 Charlie Toor 13 XT1 Charlie Toor 14 XT1 Charlie Toor 15 XT1 Charlie Toor 16 XT1 Charlie Toor 17 XT1 Charlie Toor 18

A thick CPM S35VN blade, hand ground

The Charlie's blade measures 3.25 inches, roughly 83 mm, with a handle of 4.75 inches, roughly 121 mm, and an overall open length of 8.0 inches, roughly 203 mm. Its thickness reaches 0.157 inch, or 5/32, roughly 4 mm, a figure the line has kept since the Alpha, and the knife measures 0.6 inch thick overall. The steel is CPM S35VN hardened to 58-61 HRC. The hand ground bevel rises to about 1 inch, or 25 mm, on the blade's flat. Toor deliberately leaves the edge a touch thick before the final sharpening: this reserve of material at the edge is meant to extend edge retention and make field resharpening easier.

A frame lock reinforced with a steel insert

Locking relies on a frame lock whose interface with the blade receives a hardened steel insert with an overtravel stop. This insert, also machined from CPM S35VN, is designed to limit wear at the exact point where the blade bears against the lock. It is the direct legacy of the Alpha's brief, built to withstand prying loads. The brand states that the larger bearing surface this provides removes blade play, both open and closed. The blade pivots on phosphor bronze washers, and the whole assembly is held together with 6AL-4V titanium hardware with Torx 8 heads.

A hybrid handle in G10 and titanium

The handle combines G10 and 6AL-4V titanium, following the hybrid formula introduced by the Bravo. On the Charlie, the rear spacer is entirely G10: it stiffens the frame screws and replaces the classic threaded standoffs. It ends in a large jimped ring intended for a lanyard or security cord. The pocket clip is machined from a block of 6AL-4V titanium and seated in a milled recess in the handle. The knife is offered in two colourways, Carbon and Stealth, and each example is entirely made in San Diego.

XT1 Charlie Toor folding knife: a field tool opening up to versatility

The XT1's journey shows how a folder designed for a specific mission can seek a broader use without denying its origins. Toor Knives has left untouched what forms the backbone of the knife: its thick blade, its high bevel and its reinforced lock. It has, however, evolved the blade profile and materials, arriving at a lighter, less specialised folder. The name, borrowed from the NATO alphabet and extended with a nod to Vietnam war cinema, recalls where the brand comes from: a veteran owned company speaking first to those who have worn the uniform.

More…

Éric BARSE

Editor: Éric Barse

Journalist, entrepreneur, and founder of the websites www.cafe-racer-only.com and www.scooter-3-roues.com, Eric Barse divides his time between his passions: motorcycles, travel, and watches. A graduate of the Saint-Cyr military academy and the 2nd RPIMA (Parachute Regiment) before pursuing a career in communications and digital media, he has a true passion for authentic watches that have accompanied his two-wheeled adventures for many years, from the Indian Ocean to Africa and Latin America!